Brake system of the car Peugeot 206

Tightening torques for threaded connections
Tightening torques, Nm Front brakes Fastening of forward brake disks 10 Front caliper mount 30 Fastening of a support of a forward support to a rotary fist 105 Mounting the vacuum brake booster 20 Brake Master Cylinder...

Front disc brakes — description
engine's type HFY-HFZ HFY-HFZ KFX-K6C KFX KFX NFZ RPR WJZ-WJY RHY Engine code TU1JP TU1JP TU3JP TU3JP TU3JP TU5JP90 EW10J4 DW8 DW10 TD Peculiarities Without ABS, before 1999 Since 2000 Roland Garros Automatic...

Rear brakes — description
engine's type HFY-HFZ HFY-HFZ HFY-HFZ KFX-K6C KFX-K6C KFX-K6C NFZ NFZ NFZ NFZ NFZ WJZ-WJY Engine code TU1JP TU1JP TU1JP TU3JP TU3JP TU3JP TU5JP TU5JP TU5JP TU5JP TU5JP DWS Peculiarities Pressure regulator built into the...

Removal and installation of front brake pads
When removing and installing brake pads at Peugeot service centers, use the FACOM D60 A clip. Old pad design Pic. 9.1. Old design front brake pads: 1 - spring; 2 - brake shoe The brake pads of the old design are...

Removal and installation of front brake mechanisms BOSCH
Removing the front brake mechanism is carried out in the following order: brake the car with a parking brake; raise the front of the car and place it on supports; remove the wheel; remove the brake pads; Pic. 9.7....

Removal and installation of rear disc brake pads BOSCH
When removing and installing brake pads at Peugeot service centers, use the FACOM D60 A clip. Remove the rear brake pads in the following order: 1) turn on 1st gear and set the stops under the wheels; 2) jack up the car...

Removal and installation of BOSCH rear disc brakes
Removing the rear brake mechanisms is carried out in the following order: turn on 1st gear and set the stops under the wheels; jack up the car from the side of the wheel to be removed; remove the wheel; loosen the...

Removal and installation of rear drum brake shoes BOSCH
Note. The pads must be replaced on both sides. Remove the brake pads in the following order: turn on 1st gear and set the stops under the wheels; raise the rear of the car; remove the wheel; remove the drum with the...

Removal and installation of rear drum brake pads LUCAS
Note. The pads must be replaced on both sides. Remove the brake pads in the following order: turn on 1st gear and set the stops under the wheels; raise the rear of the car; remove the wheel; remove the drum with the...

Removal and installation of the main brake cylinder
Remove the master brake cylinder in the following order: Pic. 9.25. Removing the brake master cylinder: 1 - pin connector; 2 - supply tank; 3 - cotter pin; 4 - brake pipes; 5 - nuts disconnect pin 1 (pic. 9.25) brake...

Removal and installation of the vacuum amplifier of brakes
Remove the vacuum brake booster in the following order: disconnect the wires from the battery terminals; remove the battery and pallet; remove the master brake cylinder as described above; Pic. 9.28. Removing the...

Removal and installation of the pressure regulator
On most models, the pressure regulator is located at the rear of the car, under the floor of the body, and is connected by a spring to the rear suspension. On some models, the regulators are built into the wheel...

Parking brake control and adjustment
Check the operation of the parking brake in the following order: raise the rear of the car so that the wheels are off the ground and place on supports; make sure that the friction of the brake pads of the rear brake...

Draining, filling and removing air from the hydraulic brake system
Drain the brake fluid from the hydraulic drive in the following order: Pic. 9.25. Removing the brake master cylinder: 1 - pin connector; 2 - supply tank; 3 - cotter pin; 4 - brake pipes; 5 - nuts disconnect pin 1 (see...