Electrical equipment and devices of the car Peugeot Partner 1

Specifications of electrical equipment
General information System type - 12V, «minus» on mass Lamps - Type - Power (Tue) Direction indicators - bayonet type - 21 Side turn signal repeaters - with wedge base - 5 Fog lights - H1 - 55 Front marker lamps - with...

General information about on-board electrical equipment
Attention! Before any work on the electrical system, read the precautions described in paragraph « Safety first! » at the beginning of this manual and chapter 5A . The electrical system has a supply voltage of 12 V, the...

Troubleshooting in electrical circuits — general information
Note. Before starting work, refer to the precautions given in paragraph « Safety first! » and in chapter 5A . The following checks are for testing main electrical circuits and should not be used to test sensitive...

Fuses and relays — general information
Fuses 1. Fuses are designed to break an electrical circuit when a predetermined amperage is reached to protect components and wiring that could be damaged by too much current. Any increase in current will be the result...

Switches — removal and installation
Note. Before removing any switch, disconnect the wire «masses» from the battery and connect this wire after setting the switch. Cm. « Disconnecting the battery ». Ignition switch 1. See chapter 10. Steering column...

Lamps (Outdoor Lighting) — Replacement
General information 1. When replacing any lamp, keep the following points in mind: A) Be aware that if the light has just been turned off, the lamp may be very hot. b) Be sure to check the contacts of the lamp and its...

Lamps (interior lighting) — replacement
General information 1. Refer to point 1 paragraph 5 . Interior lighting 2. Using a small screwdriver, carefully remove the cover from its original place (pic. 6.2). Pic. 6.2. Carefully remove the interior light 3. Press...

External lighting devices — removal and installation
Headlights Release models prior to September 2002 1. Remove the grille as described in chapter 11 . 2. Remove the turn signal as described later in this paragraph. 3. Turn out three bolts and remove a headlight (pic....

Headlight adjustment — general information
1. Fine adjustment of headlight beams is possible only with the help of special equipment designed for this purpose. Therefore, such work must be carried out by a Peugeot/Citroen dealer or a workshop with the...

Instrument panel — removal and installation
Removing Release models prior to September 2002 1. Disconnect the wire «masses» from battery (see « Disconnecting the battery »). 2. Remove the lower and upper steering column covers as described in chapter 11 . 3....

Multifunction display — removal and installation
Removing 1. Carefully remove the bezel of the multifunction display from the bezel (pic. 10.1). Pic. 10.1. Carefully remove the bezel of the multifunction display from the bezel 2. Remove two screws and remove the unit...

Cigarette lighter / power outlet — removal and installation
Removing 1. Remove the center console as described in chapter 11 . 2. Gently release the clips and slide the backlight out of the cigarette lighter base; be extremely careful not to break the electrical contacts. 3....

Sound signal — removal and installation
Removing 1. The horn is located behind the front bumper, on the left side. 2. Remove the front bumper as described in chapter 11 . 3. Disconnect the electrical connector (-s), then unscrew the nut and remove the horn...

Wiper arm — removal and installation
Note. The wiper arms are seated on their shafts in a very tight fit. Therefore, in order to remove them without traumatic consequences for oneself and damage to the pullers themselves, in all likelihood, a puller will...

Windshield wiper motor and drive — removal and installation
Removing 1. Remove the hood grille panel as described in chapter 11 . Wiper motor 2. Using a suitable screwdriver, remove the linkage from the ball head on the motor crank (pic. 14.2). Pic. 14.2. Remove the windshield...

Liftgate wiper motor 4 luggage compartment — removal and installation
Note. On later models, installation will require an explosive rivet gun and appropriate rivets. Removing 1. Remove the wiper arm ( see paragraph 13 ). 2. Remove the tailgate trim panel as described in chapter 11 . 3. On...

Elements of the windshield washer system — removal and installation
1. The washer reservoir is located behind the right front fender. Using one or more pumps located on the reservoir, it supplies windshield and tailgate washer fluid. Washer reservoir 2. Release bolts of fastening of the...

Audio block — removal and installation
Note. The following procedure applies to Peugeot/Citroen original equipment. Removing 1. Turn off the audio unit and ignition. 2. Genuine Peugeot/Citroen audio units have DIN standard mounting hardware. Removal requires...

Speakers — removal and installation
Removing Door speakers 1. Turn the speaker grille a quarter of a turn counterclockwise and remove it from the door trim panel. 2. Remove the four screws and remove the speaker from the panel. Disconnect the electrical...

Engine immobilizer and anti-theft alarm system — general information
Note. This information only applies to later systems installed by Peugeot/Citroen as standard equipment. On early models, a keypad was used to disable the immobilizer. At the time of this writing, there was no...

Airbag system — general information, precautions and shutdown
General information 1. Depending on the model and year of manufacture, driver airbag, passenger airbag, side airbags and curtain side airbags may be installed. 2. The driver and passenger airbag system will deploy in...

Elements of the airbag system — removal and installation
Attention! Please read the safety precautions described in paragraph 20 . Driver Airbag - Removal Release models prior to September 2002 1. Deactivate the airbag system as described in paragraph 20 . 2. If necessary,...

BSI multifunctional electronic box/fuse box
General information 1. BSI multifunctional electronic unit (abbreviation for Built-in Systems Interface (in literal translation «Interface for Embedded Systems) is an electronic control unit that controls a number of...